16 Bolt Torque Pattern

Web simpler to follow than the legacy pattern. The advantage of this is after 4 bolts are completed it is always the next loose bolt in any given quadrant that will always be the next to be tightened. East pompano beach, fl 33060. The star bolting pattern is good for use on all asme b16.5, b16.47, and heat exchanger flanges. D = nominal bolt diameter (m, ft)

Web normally, with spiral wound gaskets or kammprofile gaskets, this takes about two circular passes, but with rtj gaskets you’ll need to perform additional ringer passes. Torque pattern for 16 bolt flanges. Web 16” 1” 680 500 18” 1 1/8” 960 710 20” 1 1/8” 960 710 24” 1 1/4” 1360 1000 nominal diameter recommended torque flange bolt (nm) (lb.ft) 1/2” 1/2” 35 25 3/4” 5/8” 50 40 1” 5/8” 70 50 1 1/4” 5/8” 110 80 1 1/2” 3/4” 160 120 2” 5/8” 110 80 2. East pompano beach, fl 33060. Wrenches number of tools ?

Web flange bolt torque patterns. Clamp loads for grade c lock. Web 1) properly inspect the gasket to ensure it is in good condition. Inch bolt sizes seating torque in foot lbs. For bolt diameters greater than 1.25”, hydraulic tensioning is recommended to achieve more uniform gasket stress.

Grade 2, 5, and 8 values are for slightly lubricated bolts. Four two one wrench type ? Torque pattern for 16 bolt flanges. This pattern follows a square quadrant sequence and is used on flanges with 16 bolts or more. Clamp loads for grade c lock. Web pipe size of bolts torque torque torque torque torque torque torque torque torque torque (inches) bolts (inches) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) 0.5 4 0.50 16 47 9 52 8 42 9 37 18 53 0.75 4 0.50 22 60 12 60 11 54 13 60 25 60 1 4 0.50 30 60 15 60 13 60 17 60 27 60 Web bolt tightening sequence, or torque sequence, is defined in the torque tightening procedure. Shop for us hex bolts. Web 16” 1” 680 500 18” 1 1/8” 960 710 20” 1 1/8” 960 710 24” 1 1/4” 1360 1000 nominal diameter recommended torque flange bolt (nm) (lb.ft) 1/2” 1/2” 35 25 3/4” 5/8” 50 40 1” 5/8” 70 50 1 1/4” 5/8” 110 80 1 1/2” 3/4” 160 120 2” 5/8” 110 80 2. 1 3 8 6 5 7. Flange joints are torqued tight with the help of a torque wrench (manual or hydraulic). Web the entire bolt pattern shall be tightened at least three times around the flange at 30%, 70%, and 100% of the torque value. Wrenches number of tools ? Target % of yield ? Web flange bolt torque sequence www.hswhite.com | 954.785.6760 | [email protected] 1350 south dixie hwy.

Web Bolt Size Tpi Proof Load (Lbs) 1 Clamp Load (Lbs) 2 Tightening Torque (Ft Lbs) Galv+Waxed Galv.

** torque values for 1/4 and. Web simpler to follow than the legacy pattern. Web 1) properly inspect the gasket to ensure it is in good condition. Web normally, with spiral wound gaskets or kammprofile gaskets, this takes about two circular passes, but with rtj gaskets you’ll need to perform additional ringer passes.

Web Flange Bolt Torque Patterns.

Web the entire bolt pattern shall be tightened at least three times around the flange at 30%, 70%, and 100% of the torque value. Torque pattern for 16 bolt flanges. Yes no other lubricant ? For bolt diameters greater than 1.25”, hydraulic tensioning is recommended to achieve more uniform gasket stress.

A Visual Inspection Of The Flange Sealing Surface Should Also Be Done To Ensure It Is Free Of Any Debris, Lubricants And/Or Defects.

Web pipe size of bolts torque torque torque torque torque torque torque torque torque torque (inches) bolts (inches) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) (ft.lbs.) 0.5 4 0.50 16 47 9 52 8 42 9 37 18 53 0.75 4 0.50 22 60 12 60 11 54 13 60 25 60 1 4 0.50 30 60 15 60 13 60 17 60 27 60 The star bolting pattern is good for use on all asme b16.5, b16.47, and heat exchanger flanges. Web a complete torque tightening sequence with charts for class 150 to 2500 flanges. Flange joints are torqued tight with the help of a torque wrench (manual or hydraulic).

Metric Bolt Sizes Seating Torque In Foot Lbs.

Four two one wrench type ? Proof load (lbs) clamp load (lbs) galv + waxed: T = wrench torque (nm, lbf ft) k = constant that depends on the bolt material and size. Web tightening torque (ft lbs) bolt size:

Related Post: